
Installed a new direct wire 60A Lectron Nexus EV charger. Ran 25ft of 6 gauge SEU from the inside panel through the crawlspace to our new EV charger on the side of the house. Installed a new 60A Square D homeline breaker.
Holly Springs is a short drive down NC 55 from our Cary office. Most of our work there is in newer neighborhoods like Sunset Oaks, Twelve Oaks and Sunset Ridge.

Holly Springs is one of the newest towns we serve. Census figures put the median home at 2008, and about 77% were built since 2000. Our most frequent stops are Sunset Oaks, Twelve Oaks and Sunset Ridge.
With so much new construction, the work here is mostly about adding to a home rather than repairing old wiring. Garages get EV chargers, bedrooms and porches get ceiling fans, and backyards get circuits for saunas, hot tubs and sheds. Panels may be in the garage, a basement or inside the house, and we’ve run charger circuits from all three.
Homes built in the early 2000s are now old enough for builder-grade parts to fail. AFCI and GFCI breakers trip or stop resetting, switches wear out, and kitchens built for fewer appliances overload. In one Holly Springs kitchen, lights flickered whenever the toaster and air fryer ran together, which pointed to an overloaded circuit rather than a wiring fault.
Outlets for TVs and shelving, USB outlets, GFCI replacements, and dedicated circuits for kitchens, water heaters, saunas and mini-split disconnects. See outlets and circuits.
Fixture and chandelier swaps, and new fans in bedrooms, offices and porches. See lighting and ceiling fans.
NEMA 14-50 outlets and hardwired chargers, including a 60-amp Lectron Nexus fed through the crawlspace. See EV charger installation.
Tracing bathroom outlets that lose power, tripping breakers, failed fixtures and chirping smoke alarms. See repairs.
Electrical permits are issued by the Town of Holly Springs’ Development Services office on South Main Street. The town schedules inspections for the next business day when they’re requested before 4 p.m., so permitted work closes out quickly.
Holly Springs homes are served by Duke Energy.
4.8 on Google from 280 reviews
Spencer was amazing! First, he was early (when did that ever happen), was super nice and knowledgeable. He was alone because his counterpart was out, but worked hard to get the job done. Could barely tell he was there, left his work sight clean and neat.
Robin S., Holly Springs April 2026

Installed a new direct wire 60A Lectron Nexus EV charger. Ran 25ft of 6 gauge SEU from the inside panel through the crawlspace to our new EV charger on the side of the house. Installed a new 60A Square D homeline breaker.

Section of PVC raceway for Hot Tub Disconnect needs to be replaced.

New conduit and wiring for a hard wired EV charger

Troubleshot upstairs bathroom receptacles losing power.

We were called out to replace two switched receptacles in the master bedroom with two non switched customer supplied receptacles with USB charge ports. We installed a new receptacle in the master closet by jumping off a receptacle in the bedroom.

Installed a 40 amp 240 circuit for a sauna

Moved a switch from inside closet to outside closet and added a receptacle above closet built in for built in shelf lighting

Trouble shot chirping smoke detectors
Sometimes it's a failing breaker, and sometimes it's a real wiring or appliance problem the breaker is catching. We test the circuit to find out which before replacing anything.
Yes. We recently ran 25 feet of 6-gauge cable from an inside panel through the crawlspace to a 60-amp Lectron charger on the side of a Holly Springs home, and added a hardwired charger to a basement panel in another. The route is usually through the crawlspace or basement ceiling, then out to the garage or driveway.
The Town of Holly Springs schedules inspections for the next business day when they're requested before 4 p.m. That usually means a permitted job can be inspected and closed out within a day of finishing.
Yes. We ran a 40-amp, 240-volt circuit for a sauna in Holly Springs and have repaired hot tub disconnect wiring here. We size the circuit to the equipment's label and add the disconnect and GFCI protection it requires.
Call or text our office, or send us the details and a photo and we'll follow up to schedule a visit.